DC Motors

  • 12V DC Motor 350RPM w/Encoder (12kg*cm)

    This is a gear motor with encoder. It is a motor with a 34:1 gearbox and an integrated quadrature encoder that provides a resolution of 11 pulse single per round giving a maximum output of 374 within one round. With an Arduino controller and motor driver, applications for this include a closed-loop PID control or PWM motor speed control. This motor is an ideal option for mobile robot projects. The copper output shaft, embedded thread and reinforced connector greatly extends the motor’s service life.

    Read more
  • 250:1 Micro Metal GearMotor HP

    These tiny brushed DC gearmotors are intended for use at 6 V, though in general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 9 V range (rotation can start at voltages as low as 0.5 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and offer a choice between three different motors: high-power (HP), medium-power (MP), and standard. With the exception of the 1000:1 gear ratio versions, all of the micro metal gearmotors have the same physical dimensions, so one version can be easily swapped for another if your design requirements change.

    Read more
  • 30:1 Metal Gearmotor 37Dx52L mm 350 RPM

    This gearmotor is a powerful brushed DC motor with 30:1 metal gearbox intended for operation at 12 V. These units have a 0.61″-long, 6 mm-diameter D-shaped output shaft.

    Key specs at 12 V: 350 RPM and 300 mA free-run, 110 oz-in (8 kg-cm) and 5 A stall.

    Read more
  • DF Metal Geared 15Kg Standard Servo 180° (DSS-M15)

    INTRODUCTION
    DSS-M15 is a heavy-duty metal gear standard servo with 180°wide angle, high torque power, improved stability and durability.
    Able to take in 6V and deliver a strong torque power of over 15Kg, this tough 180°servo will never let you down when you need it. Tested with high load capacity for 12 hours long, this DSS-M15 servo demonstrates a maximum torque of 18Kg without much vibration or heat.

    Read more
  • Metal DC Geared Motor w/Encoder – 12V 122RPM 38Kg.cm

    This is a Gear Motor w/Encoder, model No. GB37Y3530-12V-90EN. It is a powerful 12V motor with a 90:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 16 counts per revolution of the motor shaft, which corresponds to 1440 counts per revolution of the gearbox’s output shaft.
    These units have a 0.61″ long, 6 mm-diameter D- shaped output shaft. This motor is intended for use at 12V, though the motor can begin rotating at voltages as low as 1V.
    The face plate has six mounting holes evenly spaced around the outer edge threaded for M3 screws. These mounting holes form a regular hexagon and the centers of neighboring holes are 15.5 mm apart.
    This motor is an ideal option for your mobile robot project.
    Note: Do not screw too far into the mounting holes as the screws can hit the gears. Manufacturer recommends screwing no further than 3mm (1/8″) into the screw hole.

    Read more
  • Metal DC Geared Motor w/Encoder – 12V 251RPM 18Kg.cm

    This is a Gear Motor w/Encoder, model No.GB37Y3530-12V-251R. It is a powerful 12V motor with a 43.8:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 16 counts per revolution of the motor shaft, which corresponds to 700 counts per revolution of the gearbox’s output shaft.
    These units have a 0.61″ long, 6 mm(0.24″)-diameter D- shaped output shaft. This motor is intended for use at 12V, though the motor can begin rotating at voltages as low as 1V.
    The face plate has six mounting holes evenly spaced around the outer edge threaded for M3 screws. These mounting holes form a regular hexagon and the centers of neighboring holes are 15.5 mm(0.61″) apart.
    This motor is an ideal option for your mobile robot project.
    Warning: Do not screw too far into the mounting holes as the screws can hit the gears. Manufacturer recommends screwing no further than 3mm (1/8″) into the screw hole.

    Read more
  • Micro Metal Gearmotor (50:1)

    This gearmotor is a miniature (0.94″ x 0.39″ x 0.47″), high-quality, low-current motor with 50:1metal gearbox, These units have a 0.365″-long, 3 mm-diameter D-shaped output shaft.

    Read more
  • Micro Servo MG-90 (2.2Kg.cm)

    Do you need a servo for a tiny little project? Or are you seeking for an affordable solution? This mini metal servo is quite impressive, it does quite the job for a large range of tasks. With metal gear, it could gives you a 2.2 Kg*cm torque. Pretty strong regarding its size. Suitable for Beam robots and other automation tasks. Keep in mind that if you need some heavy lifting you should be considering some of our other options. This servo is for you if you are planning on building smaller size robots.

    Read more
  • Pololu 12V, 100 RPM, 16 kg-cm, 100:1 Gear Motor

    This 2.22″ x 1.45″ x 1.45″ gearmotor is a powerful, high-quality motor with 100:1 metal gearbox intended for operation at 12 V. These units have a 0.61″-long, 6 mm-diameter D-shaped output shaft. This gearmotor is also available with an integrated encoder.
    Key specs at 12 V: 100 RPM and 300 mA free-run, 220 oz-in (16 kg-cm) and 5 A stall.

    Read more
  • Pololu 12V, 100 RPM, 16 kg-cm, 100:1 Gear Motor w / Encoder

    This 2.71″ × 1.45″ × 1.45″ gearmotor is a powerful 12V motor with a 100:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 6400 counts per revolution of the gearbox’s output shaft. These units have a 0.61″-long, 6 mm-diameter D-shaped output shaft. This gearmotor is also available without an encoder.
    Key specs at 12 V: 100 RPM and 300 mA free-run, 220 oz-in (16 kg-cm) and 5 A stall.

    Read more
  • Pololu 12V, 150 RPM, 14 kg-cm, 70:1 Gear Motor

    This 2.13″ x 1.45″ x 1.45″ gearmotor is a powerful, high-quality motor with 67:1 metal gearbox intended for operation at 12 V. These units have a 0.61″-long, 6 mm-diameter D-shaped output shaft. This gearmotor is also available with an integrated encoder.
    Key specs at 12 V: 150 RPM and 300 mA free-run, 200 oz-in (14 kg-cm) and 5 A stall.

    Read more
  • Pololu 12V, 150 RPM, 14 kg-cm, 70:1 Gear Motor w / Encoder

    This 2.62″ × 1.45″ × 1.45″ gearmotor is a powerful 12V motor with a 67:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 4288 counts per revolution of the gearbox’s output shaft. These units have a 0.61″-long, 6 mm-diameter D-shaped output shaft. This gearmotor is also available without an encoder.
    Key specs at 12 V: 150 RPM and 300 mA free-run, 200 oz-in (14 kg-cm) and 5 A stall.

    Read more